LV SWITCHGEAR
SUPPLY & INSTALLATION
KNOWLEDGE, EXPERIENCE AND QUALITY FROM FSECL ON EVERY INSTALLATION...
Our experienced team of engineers design bespoke panels to achieve technically accurate and competitive solutions. Working closely with our customers at all times to ensure our products achieve their exact specifications.
On-site installations and modifications are completed in line with individual requirements and tight timescale. Difficult delivery and installation requirements are always accommodated using our experienced delivery team using our purpose built lift and shift vehicles and equipment.
COMPLETE LV POWER
SYSTEM INTEGRATION
LV SWITCHGEAR UP TO 6300A. TESTED TO IEC 61439-1
FULL LV PACKAGES FROM HV/LV PACKAGE SUB-STATIONS THROUGH TO FINAL DISTRIBUTION
ON-SITE INSTALLATIONS, MODIFICATIONS AND MAINTENANCE
GENERATOR CHANGEOVER CONTROLS AND PROGRAMMING
LOW VOLTAGE GENERATOR AND UPS BESPOKE SWITCHGEAR
We operate and maintain a quality assurance procedure in accordance with BS EN 9001, accredited and audited. All site personnel are CSCS qualified and carry out works in line with industry standards and most of our first aid trained.
LV SWITCHGEAR
Every switchboard is individually designed to suit our clients' requirements including:
FORMS OF SEPARATION:
FORM 2 TO 4, TYPE 1 TO 7
RATINGS: 100A TO 6300A
CABLE ENTRIES:
TOP AND BOTTOM,
ENTRY OR EXIT
ELECTRICAL, MECHANICAL INTERLOCKING
POWER FACTOR CORRECTION
PFC
TYPE TESTED ASSEMBLIES
(IEC 61439-1)
BOARD ACCESS: FRONT AND REAR
MAINS, GEN-MAN,
AUTO-CHANGEOVER
CONTROLS
RESTRICTED, UNRESTRICTED EARTH FAULT
SURGE PROTECTION
HARMONIC CORRECTION
DISTRIBUTION BOARDS
Our distribution boards are tailored to our customers' individual requirements and are suitable for private, commercial or Industrial use.
Features can include:
SINGLE PHRASE OR THREE PHRASE
KEY LOCKABLE DOOR LOCKS
MCB, RCBO, FUSE
DISTRIBUTION BOARDS
CABLE EXTENSIONS
SPLIT LOAD AND SPLIT METERING
CONTRACTOR CONTROLS
COMPLETE WITH CONTROLS I.E PHOTOCELLS, TIMERS ETC
SURGE PROTECTION
METERING (WITH COMMS, OF GEM/MID APPROVAL, SPLIT LOAD)
All switchgear is manufactured in accordance with the international standards IEC 61439-1.
CHANGEOVER PANELS
Panels are designed to suit any requirements including:
FORMS OF SEPARATION:
FORM 2 TO 4, TYPE 1 TO 7
CABLE ENTRIES:
TOP AND BOTTOM,
ENTRY OR EXIT
ELECTRICAL AND/OR MECHANICAL INTERLOCKING
MAINS, GEN-MAN,
AUTO-CHANGEOVER
CONTROLS
RATINGS: 100A TO 6300A
Device types include motorised MCCBs, motorised ACBs, motorised switches and contactors.
G59/2 PROTECTION PANELS
Our G59/2 protection panels are used for various types of generation schemes for grid connection, ensuring G59/2 compliance:
Each panel comes complete with:
GLAND PLATES (WHICH CAN BE PRE-DRILLED TO AID CONNECTION TO SITE)
ISOLATION DEVICE
G59 PROTECTION RELAY COMPLETE WITH LCD DISPLAY
SUITABLY RATED DISCONNECTION DEVICE, C/W AUC CONTACT FOR COMMISIONING
MID APPROVED ENERGY METER
ENGINEER 13AMP SOCKET (FOR USE DURING COMMISSIONING)
Example ratings and sizes:
UP TO 50kW (500 x 500 x 150mm)
UP TO 200kW (800 x 600 x 300mm)
1MW AND ABOVE (FROM 1910 x 1850 x 650mm)
All switchboards are manufactured in accordance with the international standards IEC 61439-1.
G59/2 regulations must be adhered to throughout the UK for all generation systems that generate 16Amps per phase or above.
UPS BYPASS PANELS
10 - 60kVA 1ph OR 3ph SYSTEMS
CABLE SIZES UP TO 35/50mm²
EARLY MAKE AUX CONTACTS (BYPASS)
ENGINEERS COMM SOCKET
80 - 160kVA 1ph OR 3ph SYSTEMS
CABLE SIZES UP TO 120mm²
EARLY MAKE AUX CONTACTS (BYPASS)
ENGINEERS COMM SOCKET
200 - 300kVA 1ph OR 3ph SYSTEMS
CABLE SIZES UP TO 2 x 150mm²
EARLY MAKE AUX CONTACTS (BYPASS)
ENGINEERS COMM SOCKET
